If you are not familiar with the ipads wifi antanna, the location of the wifi antenna, removing the iPad 2 digitizer without tearing this antenna can happen very easily. The iPads wireless antenna is attached to the backside of the touch screen digitizer by adhesive tape.

For future repairs, knowing the location, applying enough heat, prying up slowly to get a peak under the digitizer in this area, and being very careful in this area is the key to removing digitizer without ripping the wifi antenna out. If you ripped ANY part of this wifi antenna while removing the ipads digizer, it is advised to replace it as your iPads wifi will not work properly.

Signal strength might be weak or not work at all.

• camera lens iphone 4s replacement.
• other products you may like.
• 13-4 applications of genetic engineering answers.
• free flowchart apps for ipad.
• Replacement parts and tools for this repair;

The iPad 2 model, has a particular area to be careful with when removing the digitizer, the area near the upper right corner, near the volume, mute buttons. The power ribbon cable is one cable that handles powering iPad on, off, sleep, volume, mute functions. One very small section of this ribbon cable is exposed between the frame and digitizer, if you rip this very small fragile cable your iPad will not power on.

Replacing this power cable is one pain in the butt! VERY small screws, parts and ribbon cable to handle.

Removing the iPads digitizer without cracking or scratching it is an almost impossible job also. All the iPads I received have cracked digitizers, so damaging the digitizer any further on removing is not a concern. Even partially ripping this antenna will damage the antenna. Follow AugustaPcRepair. Problem is, for most attempting to repair there cracked digitizer themselves and not realizing you ripped the wifi antenna or cellular data antenna near top.

Then sealing new digitizer in place and your iPad does not turn on ripped on off power cable?

Introduction

How good, or what use is the iPad without wifi, internet connection? It has no network cable jack for internet connection. Removing the new digitizer off iPad in one piece again will be very difficult IF you sealed it down. So at that low cost it is a good idea to order one if you intend on repairing your front panel touch screen digitizer. Best yet keep a few extra around especially if you are doing these type repairs for customers.

Customer Reviews

One cellular data antenna on the left, and one on the right of the front camera. To much heat begins to soften the black rubber backing on the frame, will warp or melt it out of shape. Trouble is once you get by, free up digitizer on one antenna,,, you have a second one to free up, get by on other side of camera. For it is a very delicate, meticulous repair. Disconnecting, or re-connecting the lcd screen cable when iPad is not fully powered off, can blowout the back-light filter which is a circuit on the logic board.

Producing a permanent dark, dim lcd screen. These screws are extremely small. The normal precision type screw driver set will not do. I thought the iPad 2 logic board was going to have to be removed, but there is a much easier way without having to remove the logic board. Photo above right, shows the backside of the iPads glass touch panel, where the wifi cable is attached to backside.

The wifi antenna sits just to the right of the ipad home button on iPads models 2, 3, and the iPad 4. On removing the iPads glass digitizer, the wifi cable ripped separating into 2 pieces, one on the iPad frame, the other on glass touch screen bezel area. You will see the other end of this wifi wireless cable running to, and under the iPads logic board. Remove these 4 very small antenna screws, do not lose these screws.

Repair Guides

Partially peeled up in this photo. You can actually pull up carefully on that black tape area of this cover with your fingers,, carefully. Be careful you do not damage circuits under this lid while removing! Removing this lid will then expose the backside of the wireless wifi board. Silver cover popped off, and removed.

Photo on left, this is the backside off the iPad 2 wireless, wifi board. The ipads 2 wifi board connects into a socket straight down, on the logic board. By using this Website, you are signifying understanding of this trademark disclaimer. If you continue to use the Website following the posting of changes to this policy it will be deemed your acceptance of those changes.

Applicable law may not allow the limitation of exclusion of liability or incidental or consequential damages, so the above limitation or exclusion may not apply to you. Shopping Cart. ITEM : P in stock. Include Required Toolkit?

iPad 2 CDMA Front Panel Replacement - iFixit Repair Guide

This repair requires specialized tools If you don't already own specialized tools then select With Tools. Include Battery? If your phone is a year old its a good idea to replace with a new battery. This repair can be easily completed at the same time as the screen replacement. Select Insurance This invisible protection will greatly reduce or eliminate potential damage to your phone and if you break your screen you're covered for parts and labor at any repair shop nationwide.

• How to fix your iPad or iPhone screen for £12 – rather than £196.44 – and other top repair tips.
• nokia n8 memory full close some applications.
• Apple iPad Air 2 Teardown | phon-er.com?